How to use 2 axis and 1 axis gimbals: Difference between revisions
No edit summary |
No edit summary |
||
Line 5: | Line 5: | ||
<div class="toclimit-2">__TOC__</div> | <div class="toclimit-2">__TOC__</div> | ||
= General = | |||
Some general points: | Some general points: | ||
Line 18: | Line 18: | ||
* [[How to use 1 axis gimbals]] | * [[How to use 1 axis gimbals]] | ||
= Pitch-Roll Gimbals = | |||
Please share your knowledge! | Please share your knowledge! | ||
Line 24: | Line 24: | ||
Different users might have different settings which work for them. In order to explore the various solutions, I (OlliW) suggest that each of you add your solution in a separate chapter. Your addition should start with === This is My Name === as first line. THX. | Different users might have different settings which work for them. In order to explore the various solutions, I (OlliW) suggest that each of you add your solution in a separate chapter. Your addition should start with === This is My Name === as first line. THX. | ||
= Pan-Tilt Gimbals = | |||
Please share your knowledge! | Please share your knowledge! | ||
Line 30: | Line 30: | ||
Different users might have different settings which work for them. In order to explore the various solutions, I (OlliW) suggest that each of you add your solution in a separate chapter. Your addition should start with === This is My Name === as first line. THX. | Different users might have different settings which work for them. In order to explore the various solutions, I (OlliW) suggest that each of you add your solution in a separate chapter. Your addition should start with === This is My Name === as first line. THX. | ||
= Roll-Only Gimbals = | |||
Please share your knowledge! | Please share your knowledge! | ||
Different users might have different settings which work for them. In order to explore the various solutions, I (OlliW) suggest that each of you add your solution in a separate chapter. Your addition should start with === This is My Name === as first line. THX. | Different users might have different settings which work for them. In order to explore the various solutions, I (OlliW) suggest that each of you add your solution in a separate chapter. Your addition should start with === This is My Name === as first line. THX. |
Revision as of 21:29, 5 September 2019
The information on this page refers to firmware v2.43 and higher.
Since firmware version v2.43 two- and one-axis gimbals are officially supported by the STorM32 controller.
General
Some general points:
- The unused motor axis must be disabled, i.e. the corresponding Pitch Motor Usage, Roll Motor Usage or Yaw Motor Usage parameter in the [GUI:Setup] tab must be set to “disabled”.
- A 2nd IMU is not used, even if one is present. It can be disabled (Imu2 Configuration = “off”), or not, it doesn't matter.
The following articles host comments and setups of users dating from the days when the STorM32 didn't officially support 1- and 2-axis gimbals. They might be of interest nevertheless, especially the setups, so they are linked to here:
Pitch-Roll Gimbals
Please share your knowledge!
Different users might have different settings which work for them. In order to explore the various solutions, I (OlliW) suggest that each of you add your solution in a separate chapter. Your addition should start with === This is My Name === as first line. THX.
Pan-Tilt Gimbals
Please share your knowledge!
Different users might have different settings which work for them. In order to explore the various solutions, I (OlliW) suggest that each of you add your solution in a separate chapter. Your addition should start with === This is My Name === as first line. THX.
Roll-Only Gimbals
Please share your knowledge!
Different users might have different settings which work for them. In order to explore the various solutions, I (OlliW) suggest that each of you add your solution in a separate chapter. Your addition should start with === This is My Name === as first line. THX.