NT Camera: Difference between revisions
No edit summary |
No edit summary |
||
| Line 1: | Line 1: | ||
Since firmware version v2.04e NT camera modules are supported. | Since firmware version v2.04e NT camera modules are supported. | ||
The NT camera module allows to remote control a camera. It thus serves a similar purpose as the various RC camera remote control modules, such as e.g. [http://vp-systems.eu/camremote.html CAMremote] and many others. Instead of listening to a servo RC signal however it listens to the info on the NT bus. It is thus usually connected to the NT bus near the camera NT IMU module, which yields extremely slim wiring schemes (see also [[What is STorM32 NT about?|here]]). The camera remote control is tied to the {{PARAMNAME|IR Camera Control}} function in the {{GUIFIELD|Functions}} tab, i.e. it's behavior is determined by the settings in this parameter section. | The NT camera module allows to remote control a camera. It thus serves a similar purpose as the various RC camera remote control modules, such as e.g. [http://vp-systems.eu/camremote.html CAMremote] and many others. Instead of listening to a servo RC signal however it listens to the info on the NT bus. It is thus usually connected to the NT bus near the camera NT IMU module, which yields extremely slim wiring schemes (see also [[What is STorM32 NT about?|here]]). The camera remote control is tied to the {{PARAMNAME|IR Camera Control}} function in the {{GUIFIELD|Functions}} tab, i.e. it's behavior is determined by the settings in this parameter section, see [[Advanced_Functions#IR_Camera_Remote_Control|Advanced Functions: IR Camera Remote Control]]. | ||
In addition, the NT camera module also acts as "PWM out" module. That is, it in addition outputs a servo PWM signal, which is an exact mirror of the Pwm Out signal available on the STorM32 board (with appropriate settings | In addition, the NT camera module also acts as "PWM out" module. That is, it in addition outputs a servo PWM signal, which is an exact mirror of the Pwm Out signal available on the STorM32 board (with appropriate settings). This PWM signal is tied to the {{PARAMNAME|Pwm Out Control}} function in the {{GUIFIELD|Functions}} tab, i.e. it's behavior is determined by the settings in this parameter section, see [[Advanced_Functions#Pwm_Out|Advanced Functions: Pwm Out]]. | ||
Currently, dedicated NT camera hardware has not yet emerged, but the NT camera function is also integrated in the NT IMU firmware. This means that those NT IMU modules which expose extra pins can simultaneously be used also as NT camera modules. Specifically we are talking about the "big" NT IMU module and the CC3D Atom based modules | Currently, dedicated NT camera hardware has not yet emerged, but the NT camera function is also integrated in the NT IMU firmware. This means that those NT IMU modules which expose extra pins can simultaneously be used also as NT camera modules. Specifically we are talking about the "big" v1.x NT IMU module and the CC3D Atom based modules. | ||
In v2.05e three signals are provided on the NT IMU modules at three pins, namely | In v2.05e three signals are provided on the NT IMU modules at three pins, namely | ||
* | * IR Camera: standard servo PWM signal (with ca. 60Hz frequency) | ||
* | * IR Camera: 50 ms off/on/off pulse | ||
* | * Pwm Out: standard servo PWM signal (with ca. 60Hz frequency) | ||
Revision as of 09:48, 26 April 2016
Since firmware version v2.04e NT camera modules are supported.
The NT camera module allows to remote control a camera. It thus serves a similar purpose as the various RC camera remote control modules, such as e.g. CAMremote and many others. Instead of listening to a servo RC signal however it listens to the info on the NT bus. It is thus usually connected to the NT bus near the camera NT IMU module, which yields extremely slim wiring schemes (see also here). The camera remote control is tied to the IR Camera Control function in the [Functions] tab, i.e. it's behavior is determined by the settings in this parameter section, see Advanced Functions: IR Camera Remote Control.
In addition, the NT camera module also acts as "PWM out" module. That is, it in addition outputs a servo PWM signal, which is an exact mirror of the Pwm Out signal available on the STorM32 board (with appropriate settings). This PWM signal is tied to the Pwm Out Control function in the [Functions] tab, i.e. it's behavior is determined by the settings in this parameter section, see Advanced Functions: Pwm Out.
Currently, dedicated NT camera hardware has not yet emerged, but the NT camera function is also integrated in the NT IMU firmware. This means that those NT IMU modules which expose extra pins can simultaneously be used also as NT camera modules. Specifically we are talking about the "big" v1.x NT IMU module and the CC3D Atom based modules.
In v2.05e three signals are provided on the NT IMU modules at three pins, namely
- IR Camera: standard servo PWM signal (with ca. 60Hz frequency)
- IR Camera: 50 ms off/on/off pulse
- Pwm Out: standard servo PWM signal (with ca. 60Hz frequency)