Where to get NT Modules: Difference between revisions
No edit summary |
No edit summary |
||
| Line 1: | Line 1: | ||
Pre-assembled ready-to-use NT modules are currently | Pre-assembled, ready-to-use NT modules are currently not available commercially. However, the CC3D Atom can easily be used as a NT Imu module, and may be the best choice currently, if DIY is not an option. | ||
=== CC3D Atom === | |||
The [https://wiki.openpilot.org/display/WIKI/CopterControl+-+CC3D+-+Atom+Hardware+Setup Open Pilot CC3D Atom] can be used as NT imu module, when flashed with the respective NT firmware. With the pin headers stripped off, it is also relatively small. The Mini CC3D is even smaller, without the need of hardware modifications. Unfortunately it can be first-time flashed only via SWD, i.e. a SWD programmer is needed in addition to convert it to a NT module. | |||
Both boards are available cheaply from various Asian sources, and of course also at somewhat higher prices in many "regular" shops. | |||
Some links: | |||
* [http://www.banggood.com/OpenPilot-CC3D-Atom-Mini-CC3D-FPV-Flight-Controller-CC3D-EVO-p-970762.html CC3D Atom @ banggood] (ships straight from EU or USA warehouses!) | |||
* [http://www.goodluckbuy.com/openpilot-mini-cc3d-atom-nano-cc3d-side-pin-flight-controller-for-fpv-qav-250-400-quadcopter-.html CC3D Atom @ goodluckbuy] | |||
* [http://www.aliexpress.com/wholesale?catId=0&initiative_id=SB_20150822235223&isPremium=y&SearchText=openpilot+cc3d+atom CC3D Atom @ aliexpress] | |||
* [http://www.goodluckbuy.com/mini-cc3d-32-bit-openpilot-open-source-flight-controller-processor-with-case.html Mini CC3D @ goodluckbuy] | |||
* [http://www.banggood.com/Openpilot-MINI-CC3D-NANO-Atom-Flight-Controller-for-QAV250-Multicopter-250-Frame-Kit-p-992324.html Mini CC3D @ banggood] | |||
Revision as of 21:49, 4 October 2015
Pre-assembled, ready-to-use NT modules are currently not available commercially. However, the CC3D Atom can easily be used as a NT Imu module, and may be the best choice currently, if DIY is not an option.
CC3D Atom
The Open Pilot CC3D Atom can be used as NT imu module, when flashed with the respective NT firmware. With the pin headers stripped off, it is also relatively small. The Mini CC3D is even smaller, without the need of hardware modifications. Unfortunately it can be first-time flashed only via SWD, i.e. a SWD programmer is needed in addition to convert it to a NT module.
Both boards are available cheaply from various Asian sources, and of course also at somewhat higher prices in many "regular" shops.
Some links:
- CC3D Atom @ banggood (ships straight from EU or USA warehouses!)
- CC3D Atom @ goodluckbuy
- CC3D Atom @ aliexpress
- Mini CC3D @ goodluckbuy
- Mini CC3D @ banggood
[B]Sources for cables:[/B]
Unfortunately I don't know about a good, i.e reasonably priced and readily available, source of suitable pre-configured cables with plugs. The 1mm JST has however become kind of a standard and is used by many electronics, such as flight controllers, AM gimbal controllers, etc., which gives options. Some options I know a about are:
- ReadyToFlyQuads/witespy: [url]http://www.readytoflyquads.com/cables[/url]
explore the shop carefully and study the various options for configuration which are offered, with the right clicks it offers actually some good deals
- Viacopter: [url]https://www.viacopter.eu/multirotor-shop/accessories/connectors-and-wires[/url]
- Goodluckbuy: [url]http://www.goodluckbuy.com/bgc-2-0-brushless-gimbal-driver-sensor-connection-cable-for-gimbal-controller.html[/url]
The silicon wires are not as flexible as for other imu module wires, but in lack of better options OK. Quite expensive.
- Flyduino: [url]http://flyduino.net/Brushless-Gimbal-Kamerastabilisierung[/url]