|
|
| Line 43: |
Line 43: |
| * 2 auxiliary ports (digital), BUT port | | * 2 auxiliary ports (digital), BUT port |
| | | | | |
| * supply voltage: 6 - 12 V or 2 - 3S (with motor drivers enabled) <br/>'''''Comment''': The motor drivers are enabled by closing the JP1 solder bridge. When the solder bridge is open, the board can be used with voltages up to 20 V or 4S (??).'' | | * supply voltage: <br/> |
| | with motor drivers enabled: 6 - 12 V or 2 - 3S <br/> |
| | with motor drivers disabled: 6 - 20 V or 2 - 4S <br/> |
| | '''''Comment''': The motor drivers are enabled by closing the JP1 solder bridge.'' |
| * motor current: 1.0 A (??) | | * motor current: 1.0 A (??) |
| * board dimensions: 40 mm x 28 mm, 35 mm bolt to bolt, holes Ø3 mm | | * board dimensions: 40 mm x 28 mm, 35 mm bolt to bolt, holes Ø3 mm |
Revision as of 06:59, 3 August 2025
"Original" STorM32 Boards
At present, board versions v3.3, v4.1 and v6.2 are supported (v0.17/v1.0, v1.1, v1.2, v1.3x, v2.4 boards are deprecated).
STorM32-BGC v6.2
- MCU: STM32H7A3RG at 280 MHz
- motor drivers: none
- voltage regulator: 5 V, 2.0 A low-noise switching regulator
- on-board IMU: ICM42688P/ICM42688V
- 2x NT port and 1x NT-X port
- USB-C connector, permits flashing per USB (DFU)
- UART2/ESP port
- CRSF, Futaba S-Bus
- up to four PWM/Sum-PPM inputs/outputs
- joystick port (ADC) for two axes
- 2 auxiliary ports (digital), BUT port
|
- supply voltage: 6 - 27 V or 2 - 6S
- motor current: depends on used NT motor modules
- board dimensions: 40 mm x 25 mm, 35 mm bolt to bolt, holes Ø3 mm
|
STorM32-BGC v4.1
- MCU: STM32F103RC at 72 MHz
- motor drivers: DRV8839
- voltage regulator: 5 V, 2 A (??) switching regulator
- on-board IMU: ICM42688P/ICM42688V
- 2x NT port and 1x NT-X port
- on-board USB-TTL adapter CP2102, permits flashing per USB
- USB-C connector
- UART2/ESP port
- CRSF, Futaba S-Bus
- up to four PWM/Sum-PPM inputs/outputs
- joystick port (ADC) for two axes
- 2 auxiliary ports (digital), BUT port
|
with motor drivers enabled: 6 - 12 V or 2 - 3S
with motor drivers disabled: 6 - 20 V or 2 - 4S
Comment: The motor drivers are enabled by closing the JP1 solder bridge.
- motor current: 1.0 A (??)
- board dimensions: 40 mm x 28 mm, 35 mm bolt to bolt, holes Ø3 mm
|
Comment: This board is design of KrattWorks, [1].
STorM32-BGC v3.3m, v3.3i
- MCU: STM32F103RC at 72 MHz
- motor drivers: none
- voltage regulator: 5 V, 0.6 A low-noise switching regulator
- on-board IMU: ICM42605/ICM42688P/ICM42688V (v3.3i), or MPU9250 (v3.3m)
- 2x NT port and 1x NT-X port
- on-board USB-TTL adapter CP2102, permits flashing per USB
- UART2/ESP port
- CRSF, Futaba S-Bus
- up to four PWM/Sum-PPM inputs/outputs
- joystick port (ADC) for two axes
- 2 auxiliary ports (digital), BUT port
- CAN bus port (obsolete, not supported anymore)
|
- supply voltage: 6 - 27 V or 2 - 6S
- motor current: depends on used NT motor modules
- board dimensions: 40 mm x 25 mm, 35 mm bolt to bolt, holes Ø3 mm
|
Comment: Tthe v3.3i version has a ICM42605/ICM42688P/ICM42688V on-board IMU, the v3.3m version has a MPU9250 on-board IMU.
Comment: This board has no motor drivers; NT motor modules are thus mandatorily required.