STorM32 Boards: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
|||
| (15 intermediate revisions by the same user not shown) | |||
| Line 3: | Line 3: | ||
At present, board versions v6.x are supported (v0.17/v1.0, v1.1, v1.2, v1.3x, v2.4, v3.3, v4.1 boards are not supported). | At present, board versions v6.x are supported (v0.17/v1.0, v1.1, v1.2, v1.3x, v2.4, v3.3, v4.1 boards are not supported). | ||
The STorM32 boards offer two types of NT bus ports, the {{BOX|NT}} and {{BOX|NT-X}} ports. | The STorM32 boards offer two types of NT bus ports, the {{BOX|NT}} and {{BOX|NT-X}} ports. Both of these ports '''''differ''''' from the NT bus connectors on the NT modules in that their Rx and Tx pins are swapped. | ||
{{COMMENT|The Rx, Tx pins of the {{BOX|NT}} and {{BOX|NT-X}} ports on the STorM32 board must be connected to the Tx, Rx pins on the NT modules.}} | {{COMMENT|The Rx, Tx pins of the {{BOX|NT}} and {{BOX|NT-X}} ports on the STorM32 board must be connected to the Tx, Rx pins on the NT modules.}} | ||
In addition to the boards shown here, also other variants exist, such as e.g. micro versions. | In addition to the boards shown here, also other variants exist, such as e.g. micro versions. | ||
Design schemes are located in https://github.com/olliw42/storm32bgc. | |||
=== STorM32-BGC v6.3 === | === STorM32-BGC v6.3 === | ||
| Line 26: | Line 24: | ||
* UART2/ESP port | * UART2/ESP port | ||
* CRSF, Futaba S-Bus | * CRSF, Futaba S-Bus | ||
* | * Sum-PPM, 4x PWM inputs, 1x PWM output | ||
* joystick port (analog) for two axes | * joystick port (analog) for two axes | ||
* 2 auxiliary ports (digital), BUT port | * 2 auxiliary ports (digital), BUT port (digital) | ||
| | | | ||
* supply voltage: 6 - 12 V or 2 - 3S (with motor drivers enabled) <br/>'''''Comment''': The motor drivers are enabled by closing the JP1 solder bridge | * supply voltage: 6 - 12 V or 2 - 3S (with motor drivers enabled) <br/>'''''Comment''': The motor drivers are enabled by closing the JP1 solder bridge on the bottom side of the board. When the solder bridge is open (motor drivers disabled), the board can be used with voltages up to 27 V or 6S.'' | ||
* motor current: 1.0 A (??) | * motor current: 1.0 A (??) | ||
* board dimensions: 40 mm x 28 mm, 35 mm bolt to bolt, holes Ø3 mm | * board dimensions: 40 mm x 28 mm, 35 mm bolt to bolt, holes Ø3 mm | ||
| Line 36: | Line 34: | ||
{{COMMENT|This board is design of [https://www.gohstanddesigns.com/ Gohstand Designs] and based on the v4.1 design of [https://www.krattworks.com/ KrattWorks].}} | {{COMMENT|This board is design of [https://www.gohstanddesigns.com/ Gohstand Designs] and based on the v4.1 design of [https://www.krattworks.com/ KrattWorks].}} | ||
The JP1 solder bridge is on the bottom side of the board. When closed: The motor drivers are connected to VBat and are functional. The voltage shall then not exceed 12 V or 3S. When open: The motor drivers are disabled and non-functional; the voltage can then be up to 27 V or 6S. | |||
=== STorM32-BGC v6.2 === | === STorM32-BGC v6.2 === | ||
| Line 50: | Line 50: | ||
* UART2/ESP port | * UART2/ESP port | ||
* CRSF, Futaba S-Bus | * CRSF, Futaba S-Bus | ||
* | * Sum-PPM, 4x PWM inputs, 1x PWM output | ||
* joystick port (analog) for two axes | * joystick port (analog) for two axes | ||
* 2 auxiliary ports (digital), BUT port | * 2 auxiliary ports (digital), BUT port (digital) | ||
| | | | ||
* supply voltage: 6 - 27 V or 2 - 6S | * supply voltage: 6 - 27 V or 2 - 6S | ||
Latest revision as of 08:35, 20 November 2025
"Original" STorM32 Boards
At present, board versions v6.x are supported (v0.17/v1.0, v1.1, v1.2, v1.3x, v2.4, v3.3, v4.1 boards are not supported).
The STorM32 boards offer two types of NT bus ports, the NT and NT-X ports. Both of these ports differ from the NT bus connectors on the NT modules in that their Rx and Tx pins are swapped.
Comment: The Rx, Tx pins of the NT and NT-X ports on the STorM32 board must be connected to the Tx, Rx pins on the NT modules.
In addition to the boards shown here, also other variants exist, such as e.g. micro versions.
Design schemes are located in https://github.com/olliw42/storm32bgc.
STorM32-BGC v6.3
|
|
Comment: This board is design of Gohstand Designs and based on the v4.1 design of KrattWorks.
The JP1 solder bridge is on the bottom side of the board. When closed: The motor drivers are connected to VBat and are functional. The voltage shall then not exceed 12 V or 3S. When open: The motor drivers are disabled and non-functional; the voltage can then be up to 27 V or 6S.
STorM32-BGC v6.2
|
|
Comment: This board has no motor drivers; NT motor modules are thus mandatorily required.
