Leds - Revision history

OlliW: /* Yellow Led */

2023-01-21T13:26:02Z

Yellow Led

← Older revision		Revision as of 15:26, 21 January 2023
Line 9:		Line 9:
	== Yellow Led ==		== Yellow Led ==

	This paragraph is only relevant for v1.xx boards.		This paragraph is only relevant for v1.x boards, such as the v1.3x boards.

	The yellow LED is directly connected with the HC06 Bluetooth module. Hence, it doesn't tell anything about the working of the STorM32 controller; its meaning has to be read off from the documentation for the HC06 module (see [http://www.olliw.eu/storm32bgc-wiki/index.php5/Bluetooth_Module_HC06#Technical_Documentation here]).		The yellow LED is directly connected with the HC06 Bluetooth module. Hence, it doesn't tell anything about the working of the STorM32 controller; its meaning has to be read off from the documentation for the HC06 module (see [http://www.olliw.eu/storm32bgc-wiki/index.php5/Bluetooth_Module_HC06#Technical_Documentation here]).

OlliW: /* Yellow Led */

2023-01-21T13:25:47Z

Yellow Led

← Older revision		Revision as of 15:25, 21 January 2023
Line 9:		Line 9:
	== Yellow Led ==		== Yellow Led ==

	This paragraph is only relevant for v1.~~3x boards, not for v3.x or other STorM32~~ boards.		This paragraph is only relevant for v1.xx boards.

	The yellow LED is directly connected with the HC06 Bluetooth module. Hence, it doesn't tell anything about the working of the STorM32 controller; its meaning has to be read off from the documentation for the HC06 module (see [http://www.olliw.eu/storm32bgc-wiki/index.php5/Bluetooth_Module_HC06#Technical_Documentation here]).		The yellow LED is directly connected with the HC06 Bluetooth module. Hence, it doesn't tell anything about the working of the STorM32 controller; its meaning has to be read off from the documentation for the HC06 module (see [http://www.olliw.eu/storm32bgc-wiki/index.php5/Bluetooth_Module_HC06#Technical_Documentation here]).

OlliW: /* Yellow Led */

2023-01-21T13:25:11Z

Yellow Led

← Older revision		Revision as of 15:25, 21 January 2023
Line 8:		Line 8:

	== Yellow Led ==		== Yellow Led ==
	This LED is directly connected with the HC06 Bluetooth module. Hence, it doesn't tell anything about the working of the STorM32 board, its meaning has to be read off from the documentation for the HC06 module (see [http://www.olliw.eu/storm32bgc-wiki/index.php5/Bluetooth_Module_HC06#Technical_Documentation here]).

	The permanent blinking of this LED may be annoying, and one might wish to deactivate it. On the v1.3x boards ~~on can~~ scratch through the solder jumper on the bottom, on ~~the~~ v1.1 and v1.2 boards desolder the respective resistor.		This paragraph is only relevant for v1.3x boards, not for v3.x or other STorM32 boards.

			The yellow LED is directly connected with the HC06 Bluetooth module. Hence, it doesn't tell anything about the working of the STorM32 controller; its meaning has to be read off from the documentation for the HC06 module (see [http://www.olliw.eu/storm32bgc-wiki/index.php5/Bluetooth_Module_HC06#Technical_Documentation here]).

			A permanent blinking of this LED may be annoying, and one might wish to deactivate it. On the v1.3x boards it is possible to scratch through the solder jumper on the bottom, on v1.1 and v1.2 boards one can desolder the respective resistor.

	[[File:Stom32-bgc-v130-leds-01.jpg\|600px]]		[[File:Stom32-bgc-v130-leds-01.jpg\|600px]]

OlliW at 13:10, 10 December 2022

2022-12-10T13:10:32Z

← Older revision		Revision as of 15:10, 10 December 2022
Line 1:		Line 1:
	The STorM32 ~~board has~~ two LEDs, a green LED named LED0 and a red LED named LED1, which provide info about the controller's current condition. On the v1.x boards there is also a third yellow LED, which however is related to the HC06 Bluetooth module.		The STorM32 boards have two LEDs, a green LED named LED0 and a red LED named LED1, which provide info about the controller's current condition. On the v1.x boards there is also a third yellow LED, which however is related to the HC06 Bluetooth module which can be installed on these board versions.

	== Red Led (LED1) ==		== Red Led (LED1) ==

OlliW at 12:24, 6 September 2019

2019-09-06T12:24:28Z

← Older revision		Revision as of 14:24, 6 September 2019
Line 2:		Line 2:

	== Red Led (LED1) ==		== Red Led (LED1) ==
	The red LED1 is so to say a heartbeat, it should blink at a frequency of about 1 Hz in normal operation. In case of an error condition, such as a low battery voltage or missing IMU, it blinks however much faster in order to signal the error ~~conditon~~.		The red LED1 is so to say a heartbeat, it should blink at a frequency of about 1 Hz in normal operation. In case of an error condition, such as a low battery voltage or missing IMU, it blinks however much faster in order to signal the error condition.

	== Green Led (LED0) ==		== Green Led (LED0) ==

OlliW: /* Yellow Led */

2019-08-18T08:16:23Z

Yellow Led

← Older revision		Revision as of 10:16, 18 August 2019
Line 10:		Line 10:
	This LED is directly connected with the HC06 Bluetooth module. Hence, it doesn't tell anything about the working of the STorM32 board, its meaning has to be read off from the documentation for the HC06 module (see [http://www.olliw.eu/storm32bgc-wiki/index.php5/Bluetooth_Module_HC06#Technical_Documentation here]).		This LED is directly connected with the HC06 Bluetooth module. Hence, it doesn't tell anything about the working of the STorM32 board, its meaning has to be read off from the documentation for the HC06 module (see [http://www.olliw.eu/storm32bgc-wiki/index.php5/Bluetooth_Module_HC06#Technical_Documentation here]).

	The permanent blinking of this LED may be annoying, and one might wish to deactivate it ~~(on~~ v1.3 boards scratch through the solder jumper on the bottom, ~~otherwise~~ desolder the respective resistor).		The permanent blinking of this LED may be annoying, and one might wish to deactivate it. On the v1.3x boards on can scratch through the solder jumper on the bottom, on the v1.1 and v1.2 boards desolder the respective resistor.

	[[File:Stom32-bgc-v130-leds-01.jpg\|600px]]		[[File:Stom32-bgc-v130-leds-01.jpg\|600px]]

OlliW: /* Red Led (LED1) */

2019-08-18T08:15:12Z

Red Led (LED1)

← Older revision		Revision as of 10:15, 18 August 2019
Line 2:		Line 2:

	== Red Led (LED1) ==		== Red Led (LED1) ==
	The red LED1 is so to say a heartbeat, it should blink at a frequency of about 1 Hz in normal operation. In case of an error condition, such as a low battery voltage or missing IMU, it blinks however much faster ~~(which is accompanied by a fast blinking of~~ the ~~green LED)~~.		The red LED1 is so to say a heartbeat, it should blink at a frequency of about 1 Hz in normal operation. In case of an error condition, such as a low battery voltage or missing IMU, it blinks however much faster in order to signal the error conditon.

	== Green Led (LED0) ==		== Green Led (LED0) ==

OlliW at 08:14, 18 August 2019

2019-08-18T08:14:27Z

← Older revision		Revision as of 10:14, 18 August 2019
Line 1:		Line 1:
	The STorM32 board has two LEDs, a green LED named LED0 and a red LED named LED1, which provide info about the controller's current condition. ~~There~~ is also a third yellow LED, which however is related to the HC06 Bluetooth module.		The STorM32 board has two LEDs, a green LED named LED0 and a red LED named LED1, which provide info about the controller's current condition. On the v1.x boards there is also a third yellow LED, which however is related to the HC06 Bluetooth module.

	== Red Led (LED1) ==		== Red Led (LED1) ==

OlliW at 17:00, 2 July 2016

2016-07-02T17:00:46Z

← Older revision		Revision as of 19:00, 2 July 2016
Line 1:		Line 1:
	The STorM32~~-BGC~~ board has two ~~leds~~, a green ~~led~~ named LED0 and a red ~~led~~ named LED1, which provide info about the controller's current condition. There is also a third ~~led~~, which is related to the HC06 ~~bluetooth~~ module.		The STorM32 board has two LEDs, a green LED named LED0 and a red LED named LED1, which provide info about the controller's current condition. There is also a third yellow LED, which however is related to the HC06 Bluetooth module.

	== Red Led (LED1) ==		== Red Led (LED1) ==
	The red LED1 is so to say a heartbeat, it should blink at a frequency of about 1.7 Hz in normal operation. In case of an error condition, such as low battery voltage or missing IMU, it blinks however much faster (~~and~~ is ~~acompanied~~ by a fast blinking of the green ~~led~~).		The red LED1 is so to say a heartbeat, it should blink at a frequency of about 1 Hz in normal operation. In case of an error condition, such as a low battery voltage or missing IMU, it blinks however much faster (which is accompanied by a fast blinking of the green LED).

	== Green Led (LED0) ==		== Green Led (LED0) ==
	The green LED0 tells about the current state of the controller, e.g. at startup it undergoes a sequence of ever faster blink sequences. When the ~~normal~~ state is reached the green ~~led~~ is permanently on.		The green LED0 tells about the current state of the controller, e.g. at startup it undergoes a sequence of ever faster blink sequences. When the NORMAL state is reached the green LED is permanently on. For more details see [[Getting_Started#First_Startup\|Getting Started: First Startup]].

	== Yellow Led ==		== Yellow Led ==
	This ~~led~~ is directly connected with the HC06 ~~bluetooth~~ module. Hence, it doesn't tell anything about the working of the STorM32~~-BGC~~ board, its meaning has to be read off from the documentation for the HC06 module (see [http://www.olliw.eu/storm32bgc-wiki/index.php5/Bluetooth_Module_HC06#Technical_Documentation here]).		This LED is directly connected with the HC06 Bluetooth module. Hence, it doesn't tell anything about the working of the STorM32 board, its meaning has to be read off from the documentation for the HC06 module (see [http://www.olliw.eu/storm32bgc-wiki/index.php5/Bluetooth_Module_HC06#Technical_Documentation here]).

	The permanent blinking of this ~~led~~ may be ~~anyoing~~, and one might wish to deactivate it (on v1.3 boards scratch through the solder jumper on the bottom, otherwise desolder the respective resistor).		The permanent blinking of this LED may be annoying, and one might wish to deactivate it (on v1.3 boards scratch through the solder jumper on the bottom, otherwise desolder the respective resistor).

	[[File:Stom32-bgc-v130-leds-01.jpg\|600px]]		[[File:Stom32-bgc-v130-leds-01.jpg\|600px]]

OlliW at 02:10, 11 December 2014

2014-12-11T02:10:11Z

← Older revision		Revision as of 04:10, 11 December 2014
Line 2:		Line 2:

	== Red Led (LED1) ==		== Red Led (LED1) ==
	The red LED1 is so to say a heartbeat, it should blink at a frequency of about 1.7 Hz in normal operation. In case of an error condition, such as low battery voltage or missing IMU, it blinks however much faster.		The red LED1 is so to say a heartbeat, it should blink at a frequency of about 1.7 Hz in normal operation. In case of an error condition, such as low battery voltage or missing IMU, it blinks however much faster (and is acompanied by a fast blinking of the green led).

	== Green Led (LED0) ==		== Green Led (LED0) ==
	The green LED0 ~~in principle~~ tells about the current state of the controller, e.g. at startup it undergoes a sequence of ever faster blink sequences. When the normal state is reached the green led is permanently on ~~(it is not really permanently on, it just seems so, the green led is in fact used as a debug output for the development of the firmware)~~.		The green LED0 tells about the current state of the controller, e.g. at startup it undergoes a sequence of ever faster blink sequences. When the normal state is reached the green led is permanently on.

	== Yellow Led ==		== Yellow Led ==
	This led is directly connected with the HC06 bluetooth module. Hence, it doesn't tell anything about the working of the STorM32-BGC board, its meaning has to be read off from the documentation for the HC06 module (see [http://www.olliw.eu/storm32bgc-wiki/index.php5/Bluetooth_Module_HC06#Technical_Documentation here]).		This led is directly connected with the HC06 bluetooth module. Hence, it doesn't tell anything about the working of the STorM32-BGC board, its meaning has to be read off from the documentation for the HC06 module (see [http://www.olliw.eu/storm32bgc-wiki/index.php5/Bluetooth_Module_HC06#Technical_Documentation here]).

	The permanent blinking of this led may be ~~a bit~~ anyoing, and one might wish to deactivate it (on v1.3 boards scratch through the solder jumper on the bottom, otherwise desolder the respective resistor).		The permanent blinking of this led may be anyoing, and one might wish to deactivate it (on v1.3 boards scratch through the solder jumper on the bottom, otherwise desolder the respective resistor).


	[[File:Stom32-bgc-v130-leds-01.jpg\|600px]]		[[File:Stom32-bgc-v130-leds-01.jpg\|600px]]