Flashing OlliW's NT Modules - Revision history

OlliW: /* First-Time Flashing Using a USB-TTL Adapter */

2016-03-12T20:56:31Z

First-Time Flashing Using a USB-TTL Adapter

← Older revision		Revision as of 22:56, 12 March 2016
Line 15:		Line 15:
	'''4.''' Now power up the NT module, e.g. by connecting the NT bus connector's VCC pin to the 3.3 V or 5 V pin (either is fine) on the USB-TTL adapter.		'''4.''' Now power up the NT module, e.g. by connecting the NT bus connector's VCC pin to the 3.3 V or 5 V pin (either is fine) on the USB-TTL adapter.

	'''5.''' From the STorM32 GUI select the Flash Firmware Tab and set the fields as seen below:		'''5.''' From the STorM32 GUI select the Flash Firmware Tab and set the fields as seen below. Ensure that the {{GUIPARAM\|Use NT boot mode}} check box is '''''not''''' checked.

	:[[File:Storm32-nt-firmware-first-time-flashing-gui-screen-01.jpg\|640px]]		:[[File:Storm32-nt-firmware-first-time-flashing-gui-screen-01.jpg\|640px]]

OlliW: /* First-Time Flashing Using a USB-TTL Adapter */

2016-03-12T20:53:24Z

First-Time Flashing Using a USB-TTL Adapter

← Older revision		Revision as of 22:53, 12 March 2016
Line 13:		Line 13:
	:[[File:Storm32-nt-firmware-first-time-flashing-01.jpg\|640px]]		:[[File:Storm32-nt-firmware-first-time-flashing-01.jpg\|640px]]

	'''4.''' Now power up the NT module, e.g. by connecting the NT bus connector's VCC pin to the 3.3 V or 5 V pin (either is fine) on the USB-TTL adapter.~~<br>~~		'''4.''' Now power up the NT module, e.g. by connecting the NT bus connector's VCC pin to the 3.3 V or 5 V pin (either is fine) on the USB-TTL adapter.
	~~{{COMMENT\|For the CC3D Atom this power scheme often doesn't work. Please use an external power supply, e.g. via its USB connector.}}~~

	'''5.''' From the STorM32 GUI select the Flash Firmware Tab and set the fields as seen below:		'''5.''' From the STorM32 GUI select the Flash Firmware Tab and set the fields as seen below:

OlliW: /* First-Time Flashing Using a USB-TTL Adapter */

2016-03-03T13:23:14Z

First-Time Flashing Using a USB-TTL Adapter

← Older revision		Revision as of 15:23, 3 March 2016
Line 13:		Line 13:
	:[[File:Storm32-nt-firmware-first-time-flashing-01.jpg\|640px]]		:[[File:Storm32-nt-firmware-first-time-flashing-01.jpg\|640px]]

	'''4.''' Now power up the NT module, e.g. by connecting the NT bus connector's VCC pin to the 3.3 V or 5 V pin (either is fine) on the USB-TTL adapter.		'''4.''' Now power up the NT module, e.g. by connecting the NT bus connector's VCC pin to the 3.3 V or 5 V pin (either is fine) on the USB-TTL adapter.<br>
			{{COMMENT\|For the CC3D Atom this power scheme often doesn't work. Please use an external power supply, e.g. via its USB connector.}}

	'''5.''' From the STorM32 GUI select the Flash Firmware Tab and set the fields as seen below:		'''5.''' From the STorM32 GUI select the Flash Firmware Tab and set the fields as seen below:

OlliW: /* First-Time Flashing Using SWD */

2016-01-20T22:10:11Z

First-Time Flashing Using SWD

← Older revision		Revision as of 00:10, 21 January 2016
Line 33:		Line 33:
	'''3.''' From the STorM32 GUI select the Flash Firmware Tab and set the fields as seen below:		'''3.''' From the STorM32 GUI select the Flash Firmware Tab and set the fields as seen below:

	:[[File:~~GUI_Flash_3~~.jpg\|640px]]		:[[File:Storm32-nt-firmware-first-time-flashing-swd-gui-screen-01.jpg\|640px]]

	'''4.''' Select the Flash Firmware button and a DOS window opens similar to below:		'''4.''' Select the Flash Firmware button and a DOS window opens similar to below:

OlliW at 22:09, 20 January 2016

2016-01-20T22:09:22Z

← Older revision		Revision as of 00:09, 21 January 2016
Line 16:		Line 16:

	'''5.''' From the STorM32 GUI select the Flash Firmware Tab and set the fields as seen below:		'''5.''' From the STorM32 GUI select the Flash Firmware Tab and set the fields as seen below:

			:[[File:Storm32-nt-firmware-first-time-flashing-gui-screen-01.jpg\|640px]]

	'''6.''' Select the Flash Firmware button and a DOS window opens similar to below:		'''6.''' Select the Flash Firmware button and a DOS window opens similar to below:

OlliW at 10:49, 28 November 2015

2015-11-28T10:49:42Z

← Older revision		Revision as of 12:49, 28 November 2015
Line 5:		Line 5:
	== First-Time Flashing Using a USB-TTL Adapter ==		== First-Time Flashing Using a USB-TTL Adapter ==

	'''1.''' You will need a standard USB-TTL adapter. Ensure that it is working (drivers installed, etc.).		'''1.''' You will need a standard USB-TTL adapter (see [[STorM32_FAQ#Which USB-TTL should I use.3F\|FAQ: Which USB-TTL should I use?]]). Ensure that it is working (drivers installed, etc.).

	'''2.''' Connect the serial adapter to the NT bus pins on the NT bus connector. Do not yet power the NT module.		'''2.''' Connect the serial adapter to the NT bus pins on the NT bus connector. Do not yet power the NT module.

OlliW at 07:08, 27 November 2015

2015-11-27T07:08:46Z

← Older revision		Revision as of 09:08, 27 November 2015
Line 1:		Line 1:
	On all OlliW's NT modules the BOOT0 pin is exposed as a solder jumper, and each module can thus be first-time flashed using a standard USB-TTL adapter. Most modules also have the SWD pins exposed, which allows a first-time flashing via a ST-Link adapter. Both flashing methods are fully supported by the GUI. Any subsequent flashing (updating) can be performed most easily by the procedure described in [[Updating the Firmware of NT Modules]].		On all "OlliW" NT modules the BOOT0 pin is exposed as a solder jumper, and each module can thus be first-time flashed using a standard USB-TTL adapter. Most modules also have the SWD pins exposed, which allows a first-time flashing via a ST-Link adapter. Both flashing methods are fully supported by the GUI. Any subsequent flashing (updating) can be performed most easily by the procedure described in [[Updating the Firmware of NT Modules]].

	__TOC__		__TOC__

OlliW at 07:06, 27 November 2015

2015-11-27T07:06:53Z

← Older revision		Revision as of 09:06, 27 November 2015
Line 1:		Line 1:
	On all OlliW's NT modules the BOOT0 pin is exposed as a solder ~~joint~~, and each module can thus be first-time flashed using a standard USB-TTL adapter. Most modules also have the SWD pins exposed, which allows a first-time flashing via a ST-Link adapter. Both flashing methods are fully supported by the GUI. Any subsequent flashing (updating) can be performed most easily by the procedure described in [[Updating the Firmware of NT Modules]].		On all OlliW's NT modules the BOOT0 pin is exposed as a solder jumper, and each module can thus be first-time flashed using a standard USB-TTL adapter. Most modules also have the SWD pins exposed, which allows a first-time flashing via a ST-Link adapter. Both flashing methods are fully supported by the GUI. Any subsequent flashing (updating) can be performed most easily by the procedure described in [[Updating the Firmware of NT Modules]].

	__TOC__		__TOC__

OlliW: /* First-Time Flashing Using a USB-TTL Adapter */

2015-11-27T07:06:37Z

First-Time Flashing Using a USB-TTL Adapter

← Older revision		Revision as of 09:06, 27 November 2015
Line 9:		Line 9:
	'''2.''' Connect the serial adapter to the NT bus pins on the NT bus connector. Do not yet power the NT module.		'''2.''' Connect the serial adapter to the NT bus pins on the NT bus connector. Do not yet power the NT module.

	'''3.''' Find the BOOT0 solder ~~joint~~ and close it.		'''3.''' Find the BOOT0 solder jumper and close it.

	:[[File:Storm32-nt-firmware-first-time-flashing-01.jpg\|640px]]		:[[File:Storm32-nt-firmware-first-time-flashing-01.jpg\|640px]]
Line 19:		Line 19:
	'''6.''' Select the Flash Firmware button and a DOS window opens similar to below:		'''6.''' Select the Flash Firmware button and a DOS window opens similar to below:

	'''7.''' Open the BOOT0 solder ~~joint~~ again. The NT module is now ready for usage.		'''7.''' Open the BOOT0 solder jumper again. The NT module is now ready for usage.

	== First-Time Flashing Using SWD ==		== First-Time Flashing Using SWD ==

OlliW: /* First-Time Flashing Using a USB-TTL Adapter */

2015-11-27T07:06:08Z

First-Time Flashing Using a USB-TTL Adapter

← Older revision		Revision as of 09:06, 27 November 2015
Line 11:		Line 11:
	'''3.''' Find the BOOT0 solder joint and close it.		'''3.''' Find the BOOT0 solder joint and close it.

	'''4.''' ~~Find the BOOT0 solder joint and close it.~~ Now power up the NT module, e.g. by connecting the NT bus connector's VCC pin to the 3.3 V or 5 V pin (either is fine) on the USB-TTL adapter.		:[[File:Storm32-nt-firmware-first-time-flashing-01.jpg\|640px]]

			'''4.''' Now power up the NT module, e.g. by connecting the NT bus connector's VCC pin to the 3.3 V or 5 V pin (either is fine) on the USB-TTL adapter.

	'''5.''' From the STorM32 GUI select the Flash Firmware Tab and set the fields as seen below:		'''5.''' From the STorM32 GUI select the Flash Firmware Tab and set the fields as seen below: