How to use 2 axis and 1 axis gimbals: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
|||
(5 intermediate revisions by the same user not shown) | |||
Line 3: | Line 3: | ||
Since firmware version v2.43 two- and one-axis gimbals are officially supported by the STorM32 controller, for both conventional and T-STorM32 (encodered) setups. | Since firmware version v2.43 two- and one-axis gimbals are officially supported by the STorM32 controller, for both conventional and T-STorM32 (encodered) setups. | ||
Since firmware version v2.63 the {{GUI|Configure Gimbal Tool}} supports the configuration of two- and one-axis gimbals. | Since firmware version v2.63 the {{GUI|Configure Gimbal Tool}} supports the configuration of some two- and one-axis gimbals. | ||
<div class="toclimit-2">__TOC__</div> | <div class="toclimit-2">__TOC__</div> | ||
Line 9: | Line 9: | ||
= General = | = General = | ||
General setup: | |||
* The unused motor axes must be disabled, i.e. the corresponding {{PARAMNAME|Pitch Motor Usage}}, {{PARAMNAME|Roll Motor Usage}} or {{PARAMNAME|Yaw Motor Usage}} parameter in the {{GUI|Setup}} tab must be set to {{PARAMVALUE|disabled}}. | * The unused motor axes must be disabled, i.e., the corresponding {{PARAMNAME|Pitch Motor Usage}}, {{PARAMNAME|Roll Motor Usage}} or {{PARAMNAME|Yaw Motor Usage}} parameter in the {{GUI|Setup}} tab must be set to {{PARAMVALUE|disabled}}. These, and only these settings are used by the STorM32 controller to determine which type of gimbal is used. | ||
For some 2-axis gimbal configurations, a 2nd IMU is supported, and then in fact has advantages. The 2-axis pitch-roll configuration has full 2nd Imu support. | |||
For 1-axis gimbal configurations, a 2nd IMU is not supported. | |||
<!-- | |||
The following articles host comments and setups of users dating from the days when the STorM32 didn't officially support 2- and 1-axis gimbals. They might be of interest nevertheless, especially the setups, so they are linked to here: | The following articles host comments and setups of users dating from the days when the STorM32 didn't officially support 2- and 1-axis gimbals. They might be of interest nevertheless, especially the setups, so they are linked to here: | ||
Line 37: | Line 40: | ||
Different users might have different settings which work for them. In order to explore the various solutions, I (OlliW) suggest that each of you add your solution in a separate chapter. Your addition should start with === This is My Name === as first line. THX. | Different users might have different settings which work for them. In order to explore the various solutions, I (OlliW) suggest that each of you add your solution in a separate chapter. Your addition should start with === This is My Name === as first line. THX. | ||
--> |
Latest revision as of 13:29, 11 November 2023
The information on this page refers to firmware v2.43e and higher.
Since firmware version v2.43 two- and one-axis gimbals are officially supported by the STorM32 controller, for both conventional and T-STorM32 (encodered) setups.
Since firmware version v2.63 the [GUI:Configure Gimbal Tool] supports the configuration of some two- and one-axis gimbals.
General
General setup:
- The unused motor axes must be disabled, i.e., the corresponding Pitch Motor Usage, Roll Motor Usage or Yaw Motor Usage parameter in the [GUI:Setup] tab must be set to “disabled”. These, and only these settings are used by the STorM32 controller to determine which type of gimbal is used.
For some 2-axis gimbal configurations, a 2nd IMU is supported, and then in fact has advantages. The 2-axis pitch-roll configuration has full 2nd Imu support.
For 1-axis gimbal configurations, a 2nd IMU is not supported.