Docu for witespy board(s): Difference between revisions

From STorM32-BGC Wiki V1
Jump to navigation Jump to search
No edit summary
No edit summary
Line 34: Line 34:
== Pins and Connectors ==
== Pins and Connectors ==


:[[File:Stom32-bgc-witespy-ports-and-connections-01.jpg|600px]]
[[File:Stom32-bgc-witespy-ports-and-connections-01.jpg|600px]]


== Flashing Firmware ==
== Flashing Firmware ==
Line 40: Line 40:
Follow the instructions for {{WARNING|v1.1 boards}} in the [[How to flash firmware]] manual.
Follow the instructions for {{WARNING|v1.1 boards}} in the [[How to flash firmware]] manual.


:[[File:Stom32-bgc-witespy-flashing-w-usbttladapter-connections-01.jpg|600px]]
[[File:Stom32-bgc-witespy-flashing-w-usbttladapter-connections-01.jpg|600px]]


== On-board Bluetooth ==
== On-board Bluetooth ==
Line 48: Line 48:
For further info on the HC06 bluetooth module, and its installation and configuration, see [[Bluetooth Module HC06]].
For further info on the HC06 bluetooth module, and its installation and configuration, see [[Bluetooth Module HC06]].


:[[File:Storm32bgc-v11-witespy-diode-location.jpg|450px]]
[[File:Storm32bgc-v11-witespy-diode-location.jpg|450px]]

Revision as of 19:34, 19 July 2014

This page provides documentation for the STorM32-BGC board sold by Witespy - Ready To Fly Quads.

Dos and Don'ts

Please read the tutorial's Dos and Don'ts.

Shop Link

http://witespyquad.gostorego.com/flight-controllers/storm32-bgc-3-axis-stm32-brushless-gimbal-controller.html

Board Configuration

  • board version: v1.1
  • board color: blue
  • motor drivers in DFN packages: yes
  • on-board MPU: yes
  • on-board bluetooth module: no
  • I2C plug type: picoblade (1.25mm JST)
  • I2C#2 plug type: picoblade (1.25mm JST)
  • pin headers: no

Included accessories:

  • MPU module
  • cable with connectors for MPU module

Comments:

  • diode for on-board bluetooth module not populated (see below)

Specifications

  • supply voltage: 6 - 18 V or 2 - 4S
  • motor current: max. 1.5 A per motor
    Comment: This is not yet fully exploited, motors with resistances of 12 Ohm or larger have been tested to be well handled at 4S (see here, here), motors with 10 Ohm may be handled with care (see here and here).
  • board dimensions: 50 mm x 50 mm, 45 mm bolt to bolt, holes Ø3 mm

Pins and Connectors

Stom32-bgc-witespy-ports-and-connections-01.jpg

Flashing Firmware

Follow the instructions for v1.1 boards in the How to flash firmware manual.

Stom32-bgc-witespy-flashing-w-usbttladapter-connections-01.jpg

On-board Bluetooth

The witespy board can be equipped with a HC06 bluetooth module on the bottom side of the board. However, a diode, which is needed for the on-board bluetooth module to work, is not populated. Its location is shown in the photo below. In principle any diode which fits on the pads can be used, but preferably a Shottky diode is choosen. The "original" type is PMEG3010ER. A possibly simpler solution is to just short circuit the two pads by e.g. soldering a piece of wire across them. However, the communication via the UART port wouldn't work then anymore, i.e. this should only be done if one is not going to use the UART port anytime.

For further info on the HC06 bluetooth module, and its installation and configuration, see Bluetooth Module HC06.

Storm32bgc-v11-witespy-diode-location.jpg